GTrusted
The Insignia Switch Dock Kit AC Adapter was bundled with the Insignia Switch Dock Kit to keep the dock charged up to 39W using USB Power Delivery over the USB Type-C interface. The power adapter claims to support the common USB Power Delivery profiles of 15 watts (5 volts @ 3 amps), 27 watts (9 volts @ 3 amps), and 39 watts (15 volts @ 2.6 amps), which we verified using the USB Power Delivery Compliance C2 Tester from Granite River Labs to run just a subset of the full USB Power Delivery compliance test suite. Note some compliance failures were observed.
![]()
DUT Information
Manufacturer
|
Insignia
|
Model Number
|
40W PD Charger
|
Serial Number
|
Comm
|
Test Information
Date and Time:
|
20180627_185221
|
Controller and Instrument Information
Parameter
|
Value
|
|---|---|
GRL USB-PD_C2 Serial No.
|
080.069.080.065.132.
|
GRL USB-PD Software Version
|
1.3.4.5
|
GRL USB-PD Firmware Version
|
1.3.5.0.12
|
Board Calibration
|
Calibration Success.
|
App Mode
|
COMMUNICATION_ENGINE_TESTS
|
Tx Mask
|
true
|
Rx Mask
|
false
|
RX mask Power selection
|
Neutral Power
|
Device Type
|
Provider Only
|
Cable IR drop Imp(R)
|
0
|
Cable Type.
|
USB-Type-C-Cable
|
COMMUNICATION_ENGINE_TESTS CTS Version
|
1.06
|
Noise Pattern Generation:
|
GEN-2 Noise
|
VIF info
|
*Since VIF was not loaded below test results are information Only.
|
Product Capabilities
Parameter
|
GetCapabilities
|
|---|---|
Type_C
|
NONE
|
SOP_Capable
|
NONE
|
SOP_P_Capable
|
NONE
|
SOP_PP_Capable
|
NONE
|
SOP_P_Debug_Capable
|
NONE
|
SOP_PP_Debug_Capable
|
NONE
|
Manufacturer_Info_Supported_Port
|
NONE
|
USB_Comms_Capable
|
NO
|
DR_Swap_To_DFP_Supported
|
NO
|
DR_Swap_To_UFP_Supported
|
NO
|
Externally_Powered
|
YES
|
VCONN_Swap_To_On_Supported
|
NONE
|
VCONN_Swap_To_Off_Supported
|
NONE
|
Responds_To_Discov
|
NONE
|
Attempts_Discov
|
NONE
|
Chunking_Implemented_SOP
|
NO
|
Unchunked_Extended_Messages_Supported
|
NO
|
Accepts_PR_Swap_As_Src
|
NO
|
Accepts_PR_Swap_As_Snk
|
NO
|
Requests_PR_Swap_As_Src
|
NONE
|
Requests_PR_Swap_As_Snk
|
NONE
|
Data_Capable_as_USB_Host
|
NONE
|
Data_Capable_as_USB_Device
|
NONE
|
Modal_Operation_Supported
|
NONE
|
Security_Msgs_Supported_SOP
|
NO
|
SVIDs Min
|
0
|
SVIDs Max
|
0
|
SVID Fixed
|
NONE
|
Power Capabilities
Parameter
|
GetCapabilities
|
|---|---|
No_USB_Suspend_May_Be_Set
|
NONE
|
GiveBack_May_Be_Set
|
NONE
|
Higher_Capability_Set
|
NONE
|
USB Suspend may be cleared
|
NO
|
Send Ping
|
NONE
|
Supply Type #1
|
Fixed
|
Peak Current #1
|
0x0(A)
|
Voltage #1
|
0x64(5V)
|
Max Current #1
|
0x12C(3A)
|
Supply Type #2
|
Fixed
|
Peak Current #2
|
0x0(A)
|
Voltage #2
|
0xB4(9V)
|
Max Current #2
|
0x12C(3A)
|
Supply Type #3
|
Fixed
|
Peak Current #3
|
0x0(A)
|
Voltage #3
|
0x12C(15V)
|
Max Current #3
|
0x104(2.6A)
|
No_USB_Suspend_May_Be_Set
|
NONE
|
GiveBack_May_Be_Set
|
NONE
|
Higher_Capability_Set
|
NONE
|
USB-IF High Level Mapping Summary
Sl No
|
Test Category
|
Test Group Description
|
Test Result
|
|---|---|---|---|
1
|
PHY_PRIMARY_TX
|
BMC Physical Layer Transmitter
|
PASS
|
2
|
PHY_PRIMARY_RX
|
BMC Physical Layer Receiver
|
FAIL
|
3
|
PHY_PRIMARY_MISC
|
BMC Phyiscal Layer Miscellaneous
|
PASS
|
4
|
PROT_PRIMARY
|
Protocol Specific Primary
|
PASS
|
5
|
POWER_PRIMARY
|
Power Source/Sink Primary
|
PASS
|
Result Summary
Sl No
|
Test ID
|
Test Name
|
Test Result
|
|---|---|---|---|
1
|
TDA.2.1.1.1
|
BMC-PHY-TX-EYE
|
PASS
|
2
|
TDA.2.1.1.2
|
BMC-PHY-TX-BIT
|
PASS
|
3
|
TDA.2.1.2.2
|
BMC-PHY-RX-INT-REJ
|
FAIL
|
4
|
TDA.2.1.2.1
|
BMC-PHY-RX-BUSIDL
|
PASS
|
5
|
TDA.2.1.3.1
|
BMC-PHY-TERM
|
PASS
|
7
|
TDA.2.2.1
|
BMC-PROT-SEQ-GETCAPS
|
PASS
|
11
|
TDA.2.2.7
|
BMC-PROT-BIST-NOT-5V-SRC
|
PASS
|
13
|
TDA.2.3.1.1
|
POW-SRC-LOAD-P-PC
|
PASS
|
14
|
TDA.2.3.2.1
|
POW-SRC-TRANS-P-PC
|
PASS
|
15
|
TDB.2.2.9
|
BMC-PROT-GSC-REC
|
PASS
|
BMC Eye Diagram
![]()
The load trace diagram below was captured using the GRL-USB-PD C2 Compliance Test Solution App that shows the Insignia Switch Dock Kit AC Adapter supporting various voltage and current levels for charging.
